Communications

Liste des conférences et articles des enseignants-chercheurs du pôle MAS par année

2024

ARTICLES

1. Bontemps, A., Pitti, R. M., Fournely, E., Godi, G., & Gril, J. (2024). Multi-step creep tests of notched beams of silver fir (Abies alba) at different initial moisture contents. Construction and Building Materials, 425, 136026.doi: 10.1016/j.conbuildmat.2024.136026, https://hal.science/ACL-SPI/hal-04775871v1
   
2. Asseko, M., Bontemps, A., Godi, G., Pitti, R. M., Goli, G., Ikogou, S., … & Gril, J. Diffusion properties of Gabonese tropical hardwoods and European softwoods measured with low-tech equipment and by an inverse method. Bois et Forêts des Tropiques, 360 (2024), 1-12.,doi : 10.19182/bft2024.360.a37392, https://hal.science/hal-04733166v1
   
3. J.-P. Noyel, A. Hajjar, R. Debastiani, K. Antouly, and A. Atli, Impact of viscoelasticity on the stiffness of polymer nanocomposites : Insights from experimental and micromechanical model approaches, Polymer, 309 (2024) 127443 doi: 10.1016/j.polymer.2024.127443 – https://hal.science/hal-04739106v1
   
4. Aurélien Etiemble, Sandra Simon, Claire Rigollet, Influence Of Feedstock Formulation On Steel Processability By Extrusion Based Additive Manufacturing, Euro PM2024 Proceedings (2024), doi: 10.59499/EP246281341
   
5. Jordan Lacorne , Aurélien Etiemble, Sandra Simon, Romain Faye, Xavier Boulnat, Eric Maire, Insight Into Sintering Mechanism And Optimization Of Fused Filament Fabrication Of H13 Tool Steel, Euro PM2024 Proceedings (2024), doi: 10.59499/EP246281354
   
6. F. Majdoub, M. Belin, J. Perret-Liaudet, (2024). Ultra-low friction in soft contact lenses: Analysis of dynamic free responses measured by the dynamic oscillating tribometer”. Journal of the Mechanical Behavior of Biomedical Materials, 149, 106236. Doi: 10.1016/j.jmbbm.2023.106236, https://hal.science/hal-04814131v1/file/Article_SCL%20friction_MAJDOUB%20etal._Revised_Manuscript.pdf
   
7. K. Ruholla, M. Izadi , S. Altnji, F. Majdoub, A. Hajjar, F. Alqurashi, M. H. Mohamed “All-around review on applying passive strategies to improve heat exchanger performance using inserts and turbulators applied in thermal storage”. International Communications in Heat and Mass Transfer, 159C (2024) 108234 doi: 10.1016/j.icheatmasstransfer.2024.108234
   
8. Alizée Bouchot, Amandine Ferrieux, Johan Debayle , Guilhem Mollon, Sylvie Descartes, Can machine learning predict friction from third body morphology?, Tribology International 193 (2024) 109361, doi: 10.1016/j.triboint.2024.109361, https://hal.science/hal-04466318v1/file/CanMLpredictFrictionFromTB_VFinale_HAL.pdf

CONGRÈS

1. F. Majdoub, S. Chuepeng, N. Chantarapanich, G. Nkou Bouala, F. Dubreuil, & J. Perret-Liaudet. Triacetin as lubricant additives: friction measurement between metal pairs, 49th Leeds-Lyon Symposium on Tribology, 2-4 September 2024, Lyon, France, oral presentation.
   
2. Aurélien Etiemble, Sandra Simon, Romain Faye, Xavier Boulnat, Eric Maire, Insight Into Sintering Mechanism And Optimization Of Fused Filament Fabrication Of H13 Tool Steel, Euro PM2024
   
3. Aurélien Etiemble, Sandra Simon, Claire Rigollet, Influence Of Feedstock Formulation On Steel Processability By Extrusion Based Additive Manufacturing, Euro PM2024
   
4. Aurélien Etiemble, Sandra Simon, Claire Rigollet, Challenges of formulation and rheological behavior of feedstocks for metal additive manufacturing by material extrusion, Journées Rheo-Fab

2023

ARTICLES

1. Majdoub, F., Belin, M., & Perret-Liaudet, J. Ultra-low friction in soft contact lenses: Analysis of dynamic free responses measured by the dynamic oscillating tribometer. Journal of the Mechanical Behavior of Biomedical Materials, 149, 106236.
   
2. M Izadi, M Sheremet, A Hajjar, AM Galal, I Mahariq, F Jarad, MBB Hamida, Numerical investigation of magneto-thermal-convection impact on phase change phenomenon of Nano-PCM within a hexagonal shaped thermal energy storage. Applied Thermal Engineering 223, 119984
   
3. M Izadi, T Tayebi, HM Alshehri, A Hajjar, MB Ben Hamida, AM Galal, Transient magneto-buoyant convection of a magnetizable nanofluid inside a circle sensible storage subjected to double time-dependent thermal sources. Journal of Thermal Analysis and Calorimetry 148, 1-21
   
4. M Cheayb, D Chalmers, W De Paepe, A Hajjar, S Poncet, A new approach based on off-design R-curve and thermal load duration curve for the design and optimization of bioresources driven cogeneration Rankine cycle: Application on industrial site in Nova Scotia, Canada. Energy Conversion and Management 287, 117108
   
5. A Shafiei, A Hajjar, R Ghasemiasl, T Armaghani, A Rashad, HA Nabwey, Nanoparticles migration effects on enhancing cooling process of triangular electronic chips using novel E-shaped porous cavity, Computational Particle Mechanics 10, 793-808
   
6. M Ghalambaz, SAM Mehryan, SR Ramezani, A Hajjar, M El Kadri, M.S. Islam, O. Younis, M. Ghodrat, Phase change heat transfer in a vertical metal foam-phase change material thermal energy storage heat dissipator, Journal of Energy Storage 66, 10737
   
7. M Izadi, B Alshuraiaan, A Hajjar, MA Sheremet, MBB Hamida, Free convection of nanofluids in a porous sensible heat storage unit: Combined effect of time periodic heating and external magnetic field. International Journal of Thermal Sciences 192, 10840

CONGRÈS

1. Majdoub, F., Belin, M., & Perret-Liaudet, J. Ultra-low friction in soft contact lens-eyelid contact: analysis of dynamic free responses measured by the Dynamic Oscillating Tribometer, International Tribology Conference (ITC 2023), Fukuoka, Japan, 25th-30th September 2023.
   
2. Lacorne J., Boulnat X., Etiemble A., Simon S., Maire E. Caractérisation et optimisation du frittage d’un acier outil H13 durant le procédé de fabrication avec des fils fondus métalliques (FFFm), Métallurgie, Quel avenir ?, Grenoble, France, 5-9 Juin 2023
   
3. P. Jacquet, A. Vaucheret, M. Souêtre, J.F. Carton, How to improve the precision of numerical simulation in casting? IV International Conference of Casting and Materials Engineering ICCME 23, 6-7 November 2023, Krakow, Poland
   
4. Lacorne J., Boulnat X., Etiemble A., Simon S., Maire E. Développement et optimisation du procédé de fabrication par fils fondus métalliques (FFFm) d’un acier outil H13, Journée Initiative 3D, Saint-Etienne, France, 21 Septembre 2023
   
5. L. Fourel, J. P. Noyel, X. Kleber, P. Sainsot, and F. Ville “Experiments and modelling on Rolling Contact Fatigue,” in Journées Transmissions Mécaniques, Lyon France 12 12 juillet 2023.
   
6. L. Fourel, J. P. Noyel, X. Kleber, P. Sainsot, and F. Ville, “Modeling of Crack Initiation in Rolling Contact Fatigue-physical approach at the grain scale,” in SF2M 39e journées de printemps, Paris 24 25 mai 2023.
   
7. Etienne Lemaire, Atilla Atli, Dominique Certon “Revisiting Rochelle Salt for eco-designed disposable ultrasonic transducers“, IEEE International Ultrasonics Symposium (IUS), Montréal, Canada September 2023
   
8. Mohamed Moussa EL IDI, Ahmad HAJJAR, Atilla ATLI “Passive Thermal Management of PEMFC Using PCM- Nanoparticles Composites”, 2nd International Workshop on Health, Energy Efficiency & Intelligent Building Systems Créteil (France) July 04-06, 2023
   
9. BONTEMPS A., GODI G., MOUTOU PITTI R., FOURNELY E., GRIL J., « Analyse de la complaisance du bois dans des essais de fluage multi-paliers ». 12èmes journées du GDR 3544 « Sciences du bois » – Limoges (France), 22-24 novembre 2023.

2022

ARTICLES

1. XIONG Q., ALSHEHRI H.M., MONFAREDI R., TAYEBI T., MAJDOUB F., HAJJAR A., DELPISHEH M., IZADI M.: “Application of phase change material in improving trombe wall efficiency: An up-to-date and comprehensive overview”. Energy and Buildings, vol. 258: 111824, 27p.
2. COTTON D., JACQUET P., FAURE S., VIGNAL V.: « Ta2C precipitation after low pressure carburizing of tantalum”. Materials Chemistry and Physics, vol. 278: 125632, 9p.
3. ALSABERY A.I., HAJJAR A., RAIZAH Z., GHALAMBAZ M., HASHIM I., CHAMKHA A.: “Energy transport of wavy non-homogeneous hybrid nanofluid cavity partially filled with porous LTNE layer”. Journal of Petroleum Science and Engineering, vol.208, part D: 109655, 15p.
4. ATLI A., NOYEL J.P., HAJJAR A., ANTOULY K., LEMAIRE E., SIMON S.: « Exploring the mechanical performance of BaTiO3 filled HDPE nanocomposites: A comparative study of the experimental and numerical approaches”. Polymer, vol. 254: 125063, 12p.
5. GHALAMBAZ M., MEHRYAN S.A.M., FEEOJ R.K., HAJJAR A., HASHIM I., BABAEI MAHANI R.: “Free convective heat transfer of a non-Newtonian fluid in a cavity containing a thin flexible heater plate: an Eulerian–Lagrangian approach”. Journal of Thermal Analysis and Calorimetry, vol. 147, pp. 1809-1824
6. KHEDHER N.B., GHALAMBAZ M., ALGHAWLI A.S., HAJJAR A., SHEREMET M., MEHRYAN S.A.M.: “Study of tree-shaped optimized fins in a heat sink filled by solid-solid nanocomposite phase change material”. International Communications in Heat and Mass Transfer, vol. 136: 106195, 13p.
7. GHALAMBAZ S., HAJJAR A., YOUNIS O., ALSABERY A., GHALAMBAZ M.: “A scientometrics investigation of magnetic nanofluids”. Journal of Magnetism and Magnetic Materials, vol. 561: 169685, 15p.
8. IZADI M., HAJJAR A., ALSHEHRI H. M., SHEREMET M., GALAL A. M.: “Charging process of a partially heated trapezoidal thermal energy storage filled by nano-enhanced PCM using controlable uniform magnetic field”. International Communications in Heat and Mass Transfer, vol. 138: 106349, 14p.
9. IZADI M., HAJJAR A., ALSHEHRI H. M., SALEEM A., GALAL A. M.: “Analysis of applying fin for charging process of phase change material inside H-shaped thermal storage”. International Communications in Heat and Mass Transfer, vol. 139: 106421, 13p.
10. SOUETRE M., VAUCHERET A., JACQUET P., CARTON J.F.: « The Optimization of a Numerical Steel Foundry Simulation Through a Characterization of the Thermal Properties of the Materials”. Journal of Casting & Materials Engineering, vol. 6, n°4, pp. 76-80.

CONGRÈS

1. FOUREL L., NOYEL J.P., KLEBER X., SAINSOT P., VILLE F.: « Towards a grain-scale modeling of crack initiation in rolling contact fatigue”. STLE 76^th Annual Meeting, Orlando (USA).
2. JACQUET P., VAUCHERET A., GRIMAUD G., GALLONE T.: « Eco-Innovation for Recycling/remanufacturing Electric Vehicle Engines”. CPI’2022 International Conference on Integrated Design and Production, Rabat (Morocco).
3. SOUETRE M., VAUCHERET A., JACQUET P., CARTON J.F.: « Thermal analysis and thermal properties calculation for calibration of steel foundry simulation”. CPI’2022 International Conference on Integrated Design and Production, Rabat (Morocco).
4. PERRET-LIAUDET J., MAJDOUB F.: « Un modèle original de frottement permettant de décrire la réponse libre d’un système oscillant frottant lubrifié ». 15° Colloque National en Calcul des Structures, Presqu’île de Giens.
5. SOUETRE M., VAUCHERET A., JACQUET P., CARTON J.F.: « Optimisation de la simulation numérique de fonderie d’acier par caractérisation des propriétés thermiques des matériaux ». XV^ème Colloque Interuniversitaire Franco-Québecois, Université de Paris (France).
6. MAJDOUB F., BELIN M., PERRET-LIAUDET J.: “Ultra-low friction in soft contact lenses: analysis of dynamic responses measured by the Dynamic Oscillating Tribometer”. 7^th World Tribology Congress, Lyon (France).
7. MAJDOUB F., PERRET-LIAUDET J.: « An original state-variable friction model for lubricated sliding contacts with the film thickness as the internal variable”. 7^th World Tribology Congress, Lyon (France).
8. FOUREL L., NOYEL J.P., KLEBER X., SAINSOT P., VILLE F.: “Towards a grain-scale modeling of crack initiation in rolling contact fatigue”. 7^th World Tribology Congress, Lyon (France).
9. FOUREL L., NOYEL J.P., BOSSY E., KLEBER X., SAINSOT P., VILLE F.: “Vers une modélisation à l’échelle du grain de l’amorçage de fissure en fatigue de contact ». Congrès Français de Mécanique, CFM 2022 (Nantes).
10. MISSIAEN J.M., ETIEMBLE A., RIGOLLET C., SIMON S.: “Impression 3D par extrusion MIM like : une technologie versatile pour la fabrication additive de matériaux métalliques ». Journée thématique Initiativ3D (Grenoble).
11. ETIEMBLE A., COMMEAU T., NOUVEAU A., SIMON S., RIGOLLET C.: « Development and characterization of W-based feedstock for extrusion-based additive manufacturing”. World PM2022, Lyon (France).
12. LACORNE J., ETIEMBLE A., MAIRE E., BOULNAT X., FAYE R., SIMON S.: « 3D printing of H13 tool steel filaments: influence of debinding/sintering atmosphere on the microstructure and the mechanical properties of sintered parts”. World PM2022, Lyon (France).
13. LACORNE J., ETIEMBLE A., MAIRE E., BOULNAT X., FAYE R., SIMON S.: « Impression 3D de pièces métalliques en utilisant la technologie FFF: étude de l’influence de l’atmosphère ». Matériaux 2022 (Lille).
14. ETIEMBLE A., SIMON S., RIGOLLET C.: « Fabrication additive métallique par extrusion de matière : enjeux de la formulation, de l’impression au frittage ». Matériaux 2022 (Lille).

2021

ARTICLES

1. Coffigniez, L. Gremillard, M. Perez, S. Simon, C. Rigollet, E. Bonjour, P. Jame, X. Boulnat, Modeling of interstitials diffusion during debinding/sintering of 3D printed metallic filaments: Application to titanium alloy and its embrittlement, Acta Materialia, Volume 219, 2021, 117224.
2. G.I. Nkou Bouala, A. Etiemble, S. Dassonneville, C. Der Loughian, C. Langlois, J.-F. Pierson, P. Steyer,Structural and microstructural evolution of amorphous Zr-Cu-Ag thin-film alloys under thermal constraint: An in situ approach, Journal of Alloys and Compounds,Volume 851 (2021) 156908,https://doi.org/10.1016/j.jallcom.2020.156908.
3. Fourel, L., Noyel, J. P., Bossy, E., Kleber, X., Sainsot, P., and Ville, F., 2021, “Towards a Grain-Scale Modeling of Crack Initiation in Rolling Contact Fatigue – Part 2: Persistent Slip Band Modeling,” Tribol. Int., 163(June), p. 107173.
4. Fourel, L., Noyel, J. P., Bossy, E., Kleber, X., Sainsot, P., and Ville, F., 2021, “Towards a Grain-Scale Modeling of Crack Initiation in Rolling Contact Fatigue – Part 1: Shear Stress Considerations,” Tribol. Int., 164(August).
5. Jacquet, A. Vaucheret, J-B. Coudert, A. Mondelin, S. Chomer, Traitements de cémentation/carbonitruration sous pression réduite d’un acier inoxydable martensitique. Traitements&Matériaux 469, Mars-Avril 2021, p13-17.
6. Cotton, P. Jacquet, S. Faure, V. Vignal, Ta2C precipitation after low pressure carburizing of tantalum, Materials Chemistry and Physics, 2021, https://doi.org/10.1016/j.matchemphys.2021.125632.
7. Etienne Lemaire, Damien Thuau, Jean-Baptiste De Vaulx, Nicolas Vaissiere and Atli Atilla, Rochelle Salt-Based Ferroelectric and Piezoelectric Composite Produced with Simple Additive Manufacturing Techniques Materials 14(20) (2021) 6132, https://doi.org/10.3390/ma14206132
8. Alsabery A. I., Hajjar A., Sheremet M., Ghalambaz M., Hashim I., “Impact of particles tracking model of nanofluid on forced convection heat transfer within a wavy horizontal channel”, International Communications in Heat & Mass Transfer, vol. 122, 2021
9. Alsabery A. I., Hajjar A., Raizah Z., Ghalambaz M., Hashim I., Chamkha A., “Energy transport of wavy non-homogeneous hybrid nanofluid cavity partially filled with porous LTNE layer”, Journal of Petrolemum Sc.and Eng., Vol. 208, 2021
10. Xiong Q., Hajjar A., Alshuraiaan B., Izadi M., Altnji S, Shehzad S.A., “State-of-the-art review of nanofluids in solar collectors: A review based on the type of the dispersed nanoparticles”, Journal of Cleaner Production, 127528, 2021
11. Xiong, Q., Alshehri, H. M., Monfaredi, R., Tayebi, T., Majdoub, F., Hajjar, A., & Izadi, M. (2021). Application of Phase Change Material in Improving Trombe Wall Efficiency: An up-to-date and Comprehensive Overview. Energy and Buildings, 111824
12. Ghalambaz M., Mehryan SAM., Hajjar A., Younis O., Sheremet MA., Pour MS., & Hulme-Smith C, Phase-Transition Thermal Charging of a Channel-Shape Thermal Energy Storage Unit: Taguchi Optimization Approach and Copper Foam Inserts. Molecules, 26(5), 1235.
13. Ghalambaz M., Mehryan SAM., Hajjar A., Fteiti MA., Younis O., Sardari PT., Yaïci W., “Latent Heat Thermal Storage in Non-Uniform Metal Foam Filled with Nano-Enhanced Phase Change Material”, Sustainability, vol.13, 2021

CONGRÈS

1. Etienne Lemaire, Benjamin Dubois, Théo Luirard, Atilla Atli, Auxetic or regular partially 3D printed piezoelectric structures, International Workshop on Piezoelectric Materials and Applications in Actuators 2021 (IWPMA2021) Web Conference.

2020

ARTICLES

1. Majdoub, F., Saunier, L., Sidoroff-Coicaud, C., & Mevel, B. (2020). Experimental and numerical roller skew in tapered roller bearings. Tribology International, 145, 106142.
2. Hajjar A., Mehryan S., Ghalambaz A., “Time periodic natural convection heat transfer in a nano-encapsulated phase-change suspension”, International Journal of Mechanical Sciences, vol.166, 2020
3. Hajjar A., Jamesahar E., Shirivand H., Ghalambaz M., & Mahani R. B., “Transient phase change heat transfer in a metal foam-phase change material heatsink subject to a pulse heat flux”, Journal of Energy Storage, vol. 31, 2020
4. Ghalambaz M., Kasra AA., Hajjar A., “Melting heat transfer of a non-Newtonian phase change material in a cylindrical vertical-cavity partially filled porous media”, International Journal of Numerical Methods for Heat and Fluid Flow, vol. 30, 2019
5. Mehryan S., Heidarshenas MH., Hajjar A., Ghalambaz M., “Numerical study of melting-process of a non-Newtonian fluid inside a metal foam”, Alexandria Engineering Journal, vol.59, 2020
6. Alsabery A. I., Hashim I., Hajjar A., Ghalambaz M., Nadeem S., & Saffari Pour M., “Entropy Generation and Natural Convection Flow of Hybrid Nanofluids in a Partially Divided Wavy Cavity Including Solid Blocks”, Energies, vol. 13, 2020
7. Ghalambaz M., S Mehryan., Hajjar A., A. Veisimoradi, “Unsteady natural convection flow of a suspension comprising Nano-Encapsulated Phase Change Materials (NEPCMs) in a porous medium”, Advanced Powder Technology, vol.31, 2020
8. Ghalambaz M, S Mehryan, Tahmasebi A, Hajjar A., “Non-Newtonian phase-change heat transfer of nano-enhanced octadecane with mesoporous silica particles in a tilted enclosure using a deformed mesh technique”, Applied Mathematical Modelling, vol.85, 2020
9. Mehryan S., Ghalambaz M., Gargari LS., Hajjar A., M. Sheremet, “Natural convection flow of a suspension containing nano-encapsulated phase change particles in an eccentric annulus”, Journal of Energy Storage, vol. 28, 2020
10. SAM Mehryan., Ghalambaz M., RK Feeoj., Hajjar A., M. Izadi, “Free convection in a trapezoidal enclosure divided by a flexible partition”, International Journal of Heat and Mass Transfer, vol. 149, 2020
11. S Mehryan., Ghalambaz M ., Elsabery A., Hajjar A., M. Izadi, “Controlling the natural convection flow through a flexible baffle in an L-shaped enclosure”, Meccanica, vol.55, 2020
12. Ghalambaz, S.A.M. Mehryan, N. Mashoufi, A. Hajjar, A. Chamkha, O. Younis, “Free convective melting-solidification heat transfer of nano-encapsulated phase change particles suspensions inside a coaxial pipe”, Advanced Powder Technology, vol.31, 2020

CONGRÈS

1. Jacquet P., Vaucheret A., Coudert J.B., Mondelin A., Chomer S., Development of low pressure carburizing/carbonitriding treatments on a martensitic stainless steel for bearing applications, European Conference on Heat treatment, ECHT2020, Nov.30-Dec. 2, 2020, Antwerp, Belgium
2. Vouaillat, G., Noyel, J. P., Ville, F., Kleber, X., and Rathery, S., 2019, “From Hertzian Contact to Spur Gears: Analyses of Stresses and Rolling Contact Fatigue,” Mech. Ind., 20(6), p. 16.
3. Bossy, E., Noyel, J. P., Kleber, X., Ville, F., Sidoroff, C., and Thibault, S., 2019, “Competition between Surface and Subsurface Rolling Contact Fatigue Failures of Nitrided Parts: A Dang Van Approach,” Tribol. Int., 140.
4. S.Simon, C.Rigollet, A.Etiemble, S.Commisso, E.Maire. Optimization of feedstock formulation and processing thanks to a deeper understanding of the process. European Congress and Exhibition on Powder Metallurgy. European PM, Bilbao, 2018.
5. VAUCHERET A., NICOLI C., CARTON J.F, JACQUET P. :
   « Influence des paramètres process sur la formation des céroxides dans les aciers moulés faiblement alliés ». Tech News Fonderie, vol 11, 2019, pp31-36.
   https://fr.zone-secure.net/95203/1026888/#page=1
6. VAUCHERET A., ROSSI F., QUESADA J., ALBERTALLI E.:
   « Determination of Gray Cast Iron Age Strengthening by Nondestructive Methods: Effect of Alloying Elements ». Journal of Materials Engineering and Performance, vol. 28, no 7, 2019, pp 4026-4033.
   https://hal.archives-ouvertes.fr/hal-02284432/document
7. CADIOU F., ETIEMBLE A., DOUILLARD T., WILLOT F., VALENTIN O.:
   « Numerical Prediction of Multiscale Electronic Conductivity of Lithium-Ion Battery Positive Electrodes ». Journal of The Electrochemical Society, vol 166, no 8, 2019, pp 1692-1703.
   http://jes.ecsdl.org/content/166/8/A1692.abstract
8. BESNARD A., ARDIGO M.R., IMHOFF L., JACQUET P.:
   « Curvature Radius Measurement by Optical Profiler and Determination of the Internal Stress in thin films ». , Applied Surface Science, vol 487, 2019, pp 356-361.
   https://www.sciencedirect.com/science/article/pii/S0169433219314114?via%3Dihub
9. CANDELIER K., ATLI A., ALTEYRAC J.:
   « Termite and decay resistance of bioplast-spruce green wood-plastic composites ». European Journal of Wood and Wood Products, vol 77, Issue 1,  2019,  pp 157–169
10. CARETTE L., JACQUET P., COTTON D., VIGNAL V., FAURE S.:
    « TaC/Ta2C bilayer formed on carburized and annealed tantalum; development of a numerical growth model ». Applied Surface Science, Vol 467–468, 2019, pp 84-88.
    https://www.sciencedirect.com/science/article/pii/S0169433218329003?via%3Dihub
11. GOLABCZAK M., MAKSIM P., JACQUET P., GOLABCZAK A.,  WOZNIAK K., NOUVEAU C.:
    « Investigations of geometrical structure and morphology of samples made of hard machinable materials after Wire Electrical Discharge Machining (WEDM) and vibro-abrasive finishing ». Material Science and Engineering Technology, Vol 50, Issue 5, 2019.
    https://onlinelibrary.wiley.com/doi/abs/10.1002/mawe.201800208
12. NICOLI C., CARTON J.F, VAUCHERET A., JACQUET P.:
    « Caractérisation de la propreté inclusionnaire d’aciers de fonderie par analyse d’images en Microscopie Electronique à Balayage ». Metallurgical Research & Technology, vol 116, no 5, 2019.
    https://www.metallurgical-research.org/articles/metal/abs/2019/05/metal180315/metal180315.html
13. LEMAIRE E., AYELA C., ATLI A. :
    « Eco-friendly materials for large area piezoelectronics: self-oriented Rochelle salt in wood ». Smart Materials and Structures, vol 27, no 2, 2018.
14. ATLI A., CANDELIER K., ALTEYRAC J.:
    « Mechanical, thermal and biodegradable properties of bioplast-spruce green wood polymer composites ». International Journal of Chemical, Materials and Biomolecular Sciences. 12.5, 2018, pp 231-243.
    https://zenodo.org/record/1317160
15. GOLABCZAK M., ŚWIECIK R., GOLABCZAK A., NOUVEAU C., JACQUET P., BLANC C.:
    « Investigations of surface layer temperature and morphology of hard machinable materials used in aircraft industry during abrasive electrodischarge grinding process ». Materialwiss. Werkstofftech, vol 49, 2018, pp 568–576.
    https://onlinelibrary.wiley.com/doi/10.1002/mawe.201700249
16. VAUCHERET A., NICOLI C., CARTON J.F, JACQUET P.:
    « Influence of process parameters on ceroxide formation in low carbon steels ». Journal of Casting and Materials Engineering, vol. 1, no. 4, 2017, pp 90–96.
    http://dx.doi.org/10.7494/jcme.2017.1.4.90
17. NICOLI C., VAUCHERET A., CARTON J.F, JACQUET P.:
    « Relationship between inclusion population and deoxidation process in low carbon steels ». Journal of Casting and Materials Engineering, vol. 1, no. 4, 2017, pp 97–102.
    http://dx.doi.org/10.7494/jcme.2017.1.4.97
18. NOYEL J.P., VILLE F., JACQUET P., GRAVOUIL A., CHANGENET C.:
    « Development of a granular cohesive model for rolling contact fatigue analysis: crystal anisotropy modeling ». Tribology Transactions, vol. 59, no. 3, 2016, pp. 469-479
19. SIAD A., NOUVEAU C., BESNARD A., JACQUET P., QUESADA J.:
    « Etude d’un traitement duplex sur le comportement tribologique ». Annales de Chimie – Science des Matériaux, vol. 39, no. 3-4, 2015, pp. 201-208.
20. NOYEL J.P., JACQUET P., VILLE F., GRAVOUIL A., CHANGENET C.:
    « Modèle mésoscopique de la durée de vie en régime de fatigue de contact de roulement ». Annales de Chimie – Science des Matériaux, vol. 39, no. 3-4, 2015, pp. 193-200.
21. MARRAY T., JACQUET P., MANSORI M., FABRE A., BARRALLIER L.:
    « A thermodynamic and experimental study of low-alloy steels after carbonitriding in a low-pressure atmosphere”. Metal Science and Heat Treatment, vol.56, Issue 7-8, 2014, pp. 434-439.
22. BELIARDOUH N.E., NOUVEAU C., WALOCK M.J., JACQUET P.:
    « A study of the wear performance of duplex treated commercial low-alloy steel against alumina and WC balls”. Surface and Coatings Technology, vol.259, Part C, 2014, pp. 483-494.
23. GOLABCZAK M., GOLABCZAK A., KONSTANTYNOWICZ A., JACQUET P.:
    “Cellular automata for modelling growth of the carbon-like layers with using ideas of surface thermodynamics”. Wulfenia journal, vol.20, n°3, 2013, pp. 2
24. JACQUET P., MARRAY T., FABRE A., PEREZ G., MOINARD D.:
    “Determination of carbon and nitrogen profile after a low pressure carbonitriding treatment”. Polish ceramic bulletin, vol.115, 2013, pp. 287-294.
25. GOLABCZAK M., JACQUET P., NOUVEAU C., FLITI R.:
    “Low friction MoS2TiW coatings manufactured on X38CrMoV5-1 steel using PVD method”. Materialwissenschaft und Werktofftechnik, vol.44 (5), 2013, pp. 395-402.
26. GOLABCZAK M., JACQUET P., NOUVEAU C., FLITI R.:
    “Tribological investigations of TiC+a-C:H coatings manufactured on X38CrMoV5-1 steel using PVD technology”. Defect and Diffusion Forum, vol.334-335, 2013, pp. 97-104.
27. JACQUET P., GOLABCZAK M., LOURDIN P.:
    “Experimental characterizations of non-seizing solutions for plastic moulding tools”. Applied Surface Science, vol. 261, 2012, pp. 824-829.
28.  GOLABCZAK M., JACQUET P.:
    “Thickness evaluation of the carbon coatings manufactured on magnesium alloys using optical profiler”. Non-conventional machining processes, Journal of Machine Engineering, vol. 12 (2), 2012, pp. 29-36.
29. GOLABCZAK M., PAWLAK W., SZYMANSKI W., JACQUET P., FLITI R.: “Properties of PVD coatings manufactured on X38CrMoV5-1 steel for plastic moulding applications”. Non-conventional machining processes, Journal of Machine Engineering, vol. 12 (2), 2012, pp. 37-45.
30. CIESLIK J., JACQUET P., TLILI B., MULIN H.:
    “Decrease of compound layer thickness obtained in plasma nitriding of alloyed steels by diffusion stage”. Journal of Materials Science and Engineering, vol. 1 (7A), 2011, pp. 974-980.
31. MULIN H., JACQUET P., LAMBERTIN M., MOINARD-CHECOT D., BIHR J.C.:
    “Contribution to the development of 18 carat gold alloy shaped by MIM”. Powder Injection Moulding International vol.5 (2), 2011, pp. 66-70.
32. CIESLIK J., JACQUET P., FLECHE D.:
    “Amélioration de la durée de vie d’outils de coupe pour l’usinage du bois à l’aide de la nitruration”. Traitements & Matériaux, n°412, 2011, pp. 44-48.
33. MOINARD D.:
    “Le procédé PIM : une combinaison innovante entre métallurgie des poudres et injection plastique”. Traitements & Matériaux, n°412, 2011, pp. 26-31.
34. JACQUET P., COUDERT J.B., LOURDIN P.:
    “How different steel grades react to a salt bath nitrocarburizing and post-oxidation process: influence of alloying elements”. Surface&Coatings Technology vol.205 (16), 2011, pp. 4064-4067.
35. MOINARD-CHECOT D., RIGOLLET C., LOURDIN P.:
    “Powder injection moulding PIM of feedstock based on hydrosoluble binder and submicronic powder to manufacture parts having micro-details”. Powder Technology vol.208 (2), 2011, pp. 472-479.